Wood Burning Outdoor Fire Pit With grill Installation Guide
PREPARATION
Before assembling product, make sure all parts are present. Com pare parts with package contents
list and hardware contents list. If any part is missing or dama ged, do not attempt to assemble
Estimated Assembly Time: 30 minutes
Tools required for assembly (not included): Phillips screwdrive r, Adjustable open end wrench.
Package Contents
HARDWARE CONTENTS
PART
DESCRIPTION
QUANTITY
A
Fire Bow
1
B
Leg
4
C
Support Ring Section
4
D
Table Panel
4
E
Cooking Grate
1
F
Log Rack
1
G
Cooking Grate Stand Bar
1
H
Poker
1
AA
M6 Bolt
12
BB
Wing Bolt
6
CC
M8 Nut
8
DD
M5 Bolt
4
EE
M6 Nut
4
FF
M8 Washer
8
Installation steps
Step 1
Attach (4) legs (B) to fire bowl (A) with (8) M8 Nut (CC) and (8) M8 Washer (FF).
Step 2
Insert one support ring section(C) into another and attach the support ring assembly to leg (B) with
(2) M6 Bolt (AA) as illustrated.Repeat the same procedure to install the other support ring sections (C).
NOTE: Keep all bolts loose during the assembly of this step until all parts are installed into the correct
position.
Step 3
Secure (4) support ring sections (C) with (4) M5 Bolt (DD).
Insert the pins on table panels (D) into the fixed brackets on the fire bowl (A).
Attach (4) Wing Bolt (BB) to the fixed brackets on the fire bowl (A) as illustrated.
NOTE: The protruding pin on the table panel (D) should be placed right upon the pole on the fire bowl (A).
Using (1) AA and (1) EE
to secure 2 table panels
(D) with each other.
Step 4
Attach the cooking grate stand bar (G) to
fire bowl (A) with (1) Wing Bolt(BB) to the
fixed brackets on the fire bowl (A) and put
the log rack(F) at the bottom of the fire
bowl(A) as illustrated.
Step 5
Attach the cooking grate(E) to the cooking grate stand bar(G) with (1) Wing Bolt(BB) as illustration.
Note: Do NOT move the parts or change
the configuration during use or while the
parts are hot.
Lighting
1. Make sure there is only a small amount of ash in the bottom of the bowl. 2. Place a layer of dry kindling or a natural fire-starter onto the center of the grate. 3. Place above that a layer of dry seasoned hardwood that is put to lengths no more than 3/4 the diameter of the bowl. 4. Use a match to light kindling or fire-starter.
Tending the Fire
You may need to shift and/or add logs for an ideal experience. 1. While using a long handled fire pit tool, shift coals and logs to allow additional airflow. 2. Do NOT add gasoline, kerosene, diesel fuel, lighter fluid or alcohol to relight or enhance an existing fire. 3. Wait until glowing coals have developed before adding any additional wood. If addition wood is required, place wood on top coals, be careful not to shift ashes.
Extinguishing
1. Allow fire to burn itself out. 2. Do NOT use water to extinguish as this is dangerous and can cause damage to this outdoor fire pit.
Inspecting
This fire pit should be inspected on a regular basis to ensure product safety and longer product life.
Do NOT attempt to inspect this fire pit until the fire is COMPLETELY out and cool to the touch.
1. Check components for any signs of damage or rust.
2. If damage to any component is detected, do NOT operate until repairs are executed.
Cleaning
This fire pit should be cleaned on a regular basis to promote safer experiences and longer product life.
Note: After repeated use, a slight discoloration of the finish may occur.
Do NOT attempt to clean this fire pit until the fire is COMPLETELY out and cool to the touch.
Do NOT use oven cleaner or abrasive cleaners as they will damage this product.
Do NOT clean any part of this fire pit in a self cleaning oven as it may damage the finish.
1. Wipe exterior surfaces with a mild dishwashing detergent or baking soda.
2. For stubborn surfaces use a citrus based degreaser and a nylon scrubbing brush.
3. Rinse and clean with water.
4. Remove built-up creosote from components with a chimney cleaning product.
Storage
Do NOT move or store this fire pit until the fire is COMPLETELY out and cool to the touch.
1. Once the fire is out, coals are cold and fire pit is cool to the touch, remove ashes and properly
dispose.
2. Store the fire pit in a dry location to maximize product life.
3. Store assembled in a location away from children and pets.
